Piranha cnc touch plate instructions install#
Piranha cnc touch plate instructions code#

The incredible accuracy of the SD120 allows users to even engrave custom circuit boards. Using the included 3D carving capability and 3D model library, you can cut beautiful relief carvings, intricate inlays and create exquisitely detailed engravings with ease.

The T30501 CNC Shark SD120 features a longer 12' x 24' table designed for larger projects such as carving plaques or signs, ornamental boxes and precision parts machined from wood, soft metals or plastics. We are done, look at the video for more details.T30501 CNC Shark SD120 Put the power of the USA Made Next Wave CNC Shark SD120 to work for you today!

Piranha cnc touch plate instructions code#

A white box opens and this is where you erase everything and paste our Auto Tool Code.

Click on the flashing button РІР‚СљAuto Tool ZeroРІР‚Сњ

In Mach3 click Operator / Edit Button Script.

If you exit Mach3, you lose the settings so you have to save them, go to the РІР‚СљConfigРІР‚Сњ menu and РІР‚СљSave settingsРІР‚Сњ at the bottom. If everything works, then the program will find a location for the probe. Connect the two cords of the probe (auto tool) wire, dont worry itРІР‚в„ўs low current and safe. WhatРІР‚в„ўs happening now is that the program is waiting for you to connect the two cords (cables) so that it can locate which pin it is plugged in to. Ignore all other pins in the image above, we only need to set the probe.Р”В¬lick on РІР‚СљAutomated setup of inputsРІР‚Сњ and select probe and click Auto Set. We need to assign a port for the probe (touch off plate)

The touch of plate works as a switch and when the two cords of the cable touch we have contact. If your spindle is made of plastic, you can use a crocodile clip that you temporary fasten to the endmill. One of the cables cords must be grounded to the spindle. Pull the wire trough your cable chain all the way to your spindle. You can only use the code provided for Mach3, it probably works for Mach4 too, but we have not tested it yet.Р”Р‡asten one of the cables to any switch port of the break out board and the other to ground. If not, you can have any 2-lead cable you like, it doesnРІР‚в„ўt have to be shielded, it will only work as a switch. If you have a kit from us we usually include the cable for the probe (Auto tool). If you used the corner calibration when you started to cut you will be able to go back even if you have a power faliure. It would be difficult to manually place the end mill above the corner and therefore we use this plate. As an example, if you draw a square and a hole exactly 10 cm away from the corner of your square, then the touch off plate, or zeroing plate will tell the machine where the corner begins. As a carpenter, you have templates to do this, so the zeroing plate works a bit like a template telling the machine where the piece starts. If you have an absolute zero point, then the machine knows exactly where it is and will find the center over and over again. If you want to cut into an already existing material and have a hole exactly in the center for example, it would be very difficult to find it manually. Why is it good to have an absolute zero point? Once the steps are done you can press РІР‚СљGo to ZeroРІР‚Сњ and the machine will go to its Zero point. For option 1, The machine will calibrate all axis so wait until it has calibrated the Z-axis as well. Then click on the РІР‚СљAuto tool ZeroРІР‚Сњ button and choose from 3 options, 0=cancel, 1=Calibrate corners and height, 2=Calibrate the height. Do not start the spindle when performing this operation! Lower the end mill into one of the holes so that they are approximately 2-3mm below the hole. To zero the X, Y and Z axis you must have a 4mm or 3mm end mill. Previously, we could only zero the height but now we can also zero the X and Y axis. We have updated the touch off plate, or zeroing plate so that you can zero all axes to find your absolute zero point. The video below shows a plate with 2 calibration holes, we have changed that to only one hole since the second hole is not needed. We also include a simple cable connector (male and female crimp) that you can use if you donРІР‚в„ўt have any connector for the plate.

Piranha cnc touch plate instructions install#

The plate comes with code for install in Mach3. Touch of plate in aluminum to calibrate both height and corners. Product Description Touch off plate with code